Lighting - Lighting Accessories

The Night Saber High Capacity Spotlight Battery is the perfect power solution when you are on the go. Its 9,000mAh capacity means it can be used to power your spotlight for those night time hunting trips, recharge your mobile phone, tablet, or GPS when you don't have access to Mains power. Or even jump start any gasoline engine that is fitted with a 12-volt battery! It even features a LED flashlight with three different modes of operation.

When tested using the Night Saber 36W 3500-lumen spotlight, the battery lasted 1 hour before going dim.

Features of the High Capacity Spotlight Battery include:

Emergency Start

• Jumpstart gasoline engines in vehicle, motorcycle, boat or jetski with a 12-volt battery. USB Charging Port
• Charge your cell phone, tablet, GPS or 2-way radio. Car Charging Port
• Charge your battery pack during your commute. Spotlight Adapter
• Run your favourite spotlight on the go! Built-in LED Flashlight
• 3 modes - illumination, strobe, and S.O.S. Battery Protection
• From over-charging and over-discharging Automatic Power On / Off
• When not it use.

Specifications:

• Capacity: 9,000mAh
• Input: 14V/1A, 5V/1A
• Output: 5V/2A and 12V jump start
• Charging Time: Approx. 3 hours hours
• Start Current: 200A
• Peak Current: 400A
• Size: 130mm (L) x 68mm (W) x 24mm (D)
• Weight: 282g
• Operation Temp: -20 °C ~ 60 °C
• Lifetime: >1000 cycles

Package includes:

• 1x Power Bank
• 1x Set of plug-in alligator jumper clamps
• 1x 3-in-1 USB Combo Cable (Mini USB, Micro USB, & Apple plugs)
• 1x 12-volt Car Charger for charging from a vehicles cigarette port
• 1x 12-volt accessory plug.

*some apple products may not charge, we recommend using your genuine apple charging cable

A spare battery for your Javelot Turbo torch. It includes a tail cap so that it can be charged off the torch with the charge lead included with your Javelot Turbo. Charge your spare on the go via USB MCC cable included with every Javelot Turbo.

Specifications:
• Capacity: 10000mAh 3.6V/36Wh
• Size (LxD): 178 x 30mm
• Weight: 224.5g / 7.92oz
• Warranty: 2 years

The Night Saber Wiring Loom is the solution to all your wiring needs for Night Saber 12V Light Bars. With all the fittings included the most difficult thing in your installation will now be facing your brand new light bar down to the vehicle.

Features:
- Suitable for twin and single light sets
- High quality cable and connectors
- Pre-wired, ready to install
- Easy to understand design
- Off/on switch included
- Relay & inline fuse holders with fuse installed
- Suitable for passenger vehicles and 4x4's
- Option of universal or H4 connectors for high beam active

Accessorize your rifle with the Precision Pro M-Lok Torch Mount with Rail.

This torch mount allows you to mount any torch that has a body tube width of 1", 27mm or 30mm to your M-lok rail. This M-lok torch mount kit also has the M-lok rail separate so you can alternatively mount any weaver/picatinny style optic or laser accessory.

Features:

• 5 Slot weaver rail
• Comes with allen wrenches for easy installation
• Strong & durable anodized alloy
• Includes shims to fit 1", 27mm, & 30mm tubes
• Fits to any M-lok stock

Ideal for use on:

• Hammerli Tac R1 with M-Lok
• Tippmann M4-22 Elite with M-Lok
• H&K 416 with M-Lok
• Smith & Wesson M&P 15-22 with M-Lok
• Ruger Precision with M-Lok
• Tikka T3X Tac A1 with M-Lok
• MDT chassis with M-Lok.

Featured in the images is the Led Lenser P7 Core torch

APS 5T rechargeable lithium-ion power supplies are designed for use with thermal imaging riflescopes Pulsar Talion.

APS 5T batteries support USB Power Delivery fast charging technology when using a standard charging set (charger, USB Type-C cable, power adapter).

Specifications:

• Model: APS 5T
• SKU: 79188
• Type: Li-ion
• Nominal capacity at +22°С (72°F): 4900 mAh
• Rated voltage: 3.7 V
• Charge/discharge cycles, minimum*: 500
• Dimensions: 92 × 25 × 25 mm
• Weight: 0.08 kg (2.9 oz)

The Outdoor Outfitters Quick-Detach Torch Scope Mount for LED Lenser.
After getting frustrated with the lack of mounting options for the most popular LED Lenser Torches we have come up with a fantastic easy to use mount.

The black anodized aluminium finish matches the torch and any standard black scope’s finish.

Simply mount the included scope ring onto any 1" or 30mm scope tube. Then fit the torch mount's weaver base to the scope ring.

These are easy to install and mean you can easily remove your torch for the times when you don't need it shooting.

The torch mount is 40mm in diameter

Includes:
• 40mm Quick-Detach Scope ring
• 1" Inserts for Scope ring
• Torch Mount to fit M14, M14X, P17, P17.2, X14, X21, X21.2, X21R, X21.2R, COASTHP17, COASTHP21 or any 40mm torch body
• Allen Keys to fit

5.5m vehicle battery extension cord from Night Saber features alligator clips on one end and a female cigarette adaptor on the other end.

Specifications:
• Extension cord with positive and negative battery clamps at one end, accessory adaptor at the other
• Works with any item that plugs into a standard vehicle accessory socket
• 5.5 metres long

Free your hunting hand with the Night Saber Torch Scope Mount for LED Lenser, Night Saber and Olight torches.

Night Saber have come up with a fantastic, easy to use mount so you can hunt and spot with more ease and practically while on the move.

The scope mount and the torch mount both have inserts so you can have either ring on a 1" (25mm) or 30mm tube. Simply mount the included scope ring with a rail mount onto any 1" or 30mm scope tube. The fit the quick detach torch ring with the fastened torch onto the rail. These are very easy to install and means you can easily remove your torch for the times when you don't need it when shooting. The black anodized aluminium finish matches your torch and any standard black scope’s finish.

Includes:
• Quick-detach mounts for scope and torch
• 1" Inserts for scope and torch ring
• Height extension mount for torches with large lens diameters
• Allen keys.

Compatible with popular torches such as the Olight Javelot Pro, Olight Warrior, LED Lenser P7, Night Saber Blitzer

The Outdoor Outfitters Quick-Detach Torch Scope Mount for LED Lenser P14 or any 35mm Torch.

After getting frustrated with the lack of mounting options for the most popular LED Lenser Torches we have come up with a fantastic easy to use mount.

The black anodized aluminium finish matches the torch and any standard black scope’s finish.

Simply mount the included scope ring onto any 1" or 30mm scope tube. Then fit the torch mount's weaver base to the scope ring.

These are easy to install and mean you can easily remove your torch for the times when you don't need it shooting.

The torch mount is 35mm in diameter

Includes:
• 30mm Quick-Detach Scope ring
• 1" Inserts for Scope ring
• Torch Mount to fit P14, P14.2 or any 35mm Torch
• Allen Keys to fit

Fab Defense is one of the worlds leading manufacturers in high quality tactical accessories. Features:

Designed to hold torches with 1 1/8" diamter
Design to hold flashlights or laser devices
A Secure bolt locking system for the mounted device
Fits picatinny rails
Quick release mechanism
Tough rigid and lightweight reinforced polymer design
Special shape for easy turn-on device
Modified to fit pistol, gun, or rifle.

Charge your batteries on the go! 

With the Night Saber G4 Battery Charger, you can charge your batteries anywhere you can plug in to a powered USB port! USB cable included. 

The Night Saber G4 Battery Charger works with 3.7V rechargeable Li-ion and Li-polymer batteries: 18650, 26650, 32650, 18500, 18350, 17670, 16340.

Features:

• Keep your rechargeable batteries fully charged on the go
• Charge at home (USB adapter required), from any USB power bank, or in your car (USB adapter required)
• Charge two batteries at 1A once or four batteries at 500mA each
• Battery light indicator
• DC input: 5V/2A MicroUSB
• DC output: 4.2V/0.5A x4 (1.0A x2)

The perfect companion for your Night Saber rifle mounted Strike torch. This allows you full control right where you want it. The coiled cord stretches from 31cm up to 60cm. The waterproof rubberized switch has multiple buttons for ease of reach. The buttons will turn the unit ON/OFF or 2 fast clicks for strobe. 

Simply unscrew the end cap from your Night Saber Strike torch and replace it with the remote switch upgrade. 

The Outdoor Outfitters Torch Scope Mount for LED Lenser and Coast Torches

After getting frustrated with the lack of mounting options for the most popular LED Torches we have come up with a fantastic easy to use mount. The black anodized aluminium finish matches the torch and any standard black scope’s finish.

Simply mount the included Quick-Detach scope ring onto any 1" or 30mm scope tube. Then fit the torch mount's weaver base to the scope ring. These are easy to install and mean you can easily remove your torch for the times when you don't need it shooting.

The torch mount is 30mm in diameter. But also works on the 1” body of the Olight torch in reverse with the 1” adapter on the mount side and the 30mm ring mounted to a 30mm scope.

Includes:
• 30mm Quick-Detach Scope ring
• 1" Inserts for Scope ring
• Torch Mount to fit Fits M7, M7R, M7RX, MT7, P7, P7.2, P7QC, T7, T7.2, T7M, X7R, Coast HP7. or any 30mm Torch Body
• Allen Keys to fit.

Control your Olight Warrior X Turbo flashlight without having to move your hand with this ROD-7 Remote Pressure Switch. This switch can be used as a replacement or spare for the one that comes with the Odin and is also compatible with the Warrior X Turbo. It attaches magnetically to the tail of the light, with no need to remove the tailcap switch, and locks in position. The actual switch rests in a flexible bracket that snaps into place on a Picatinny rail in a position that's convenient for you to reach.

The Olight ROD is a remote pressure switch compatible with the Javelot Turbo and Warrior X Turbo. It simply screws onto the tail cap of your torch and gives you convenient control when using it on a rifle. It also comes with two adhesive patches for sticking the switch to your rifle. For the tactical advanage of being able to control your Olight odin without having to move your hand.

This switch can be used as a replacement or spare for the one that comes with the Odin and is also compatible with the Warrior X Turbo and Javelot Pro 2.
It attaches magnetically to the tail of the light, with no need to remove the tailcap switch, and locks in position. 

Features:

• Low click sound, long life pressure pad switch.
• Revolutionary push-to-lock remote switch for a tight fit.
• Coiled cable stretches from 9.8 in / 25cm to 31 in / 80cm.
• FIT: Olight Odin Series, Warrior X Turbo, Javelot 2 PRO

A remote switch is an add-on you won't regret having for a firearm mounted light. Have the switch where you want it, not where it has to be! 

The Olight SROD remote switch has two options, a high power button and a low power button for your choice of Illumination with one easy press. The switch magnetizes to the back of the torch as well as having a push-to-lock mechanism. Both of these systems securely attach the remote to your torch without the need for screws or other permanent options. It is also just as easy to detach from the torch! 

SROD Long Coil Wire Magnetic Remote Switch suitable for Javelot Pro 2, Warrior X 3 and Warrior 3

The RWX is Olight's brand-new pressure switch built specifically for the Warrior X (& Pro), Javelot Pro and M2R - featuring a noiseless and a sensitive pad for perfect switch manipulation. The coiled cable extends the reach of the switch to around 0.8 meters.

Features:
• Low click noise, long life electronic switch
• Powerful magnetic attachment to your Olight torch
• Coiled cable stretch from 9.8" / 25 cm to 31" / 80 cm
• Extremely low steady current 
• Compatibility: Warrior X, Warrior X Pro, Javelot Pro and M2R

Turn your flashlight into a spotlight with this solid and comfortable grip from Night Saber! This pistol grip mount fit straight onto any torch or flashlight with a 1" or 30mm tube. Having a vertical grip allows for better comfort and control for the user.

As a bonus, the grip and ring can separate into a stand alone weaver rail foregrip to put on your rifle underside rail and a scope mounted weaver rail ring so you can mount a torch or red dot optic directly over your scope. 

The perfect companion for your Night Saber rifle mounted Blitzer torch. This allows you to have full control right where you want it. The coiled cord stretches from 31cm up to 60cm. The waterproof rubberized switch has multiple buttons for ease of reach. The buttons will turn the unit ON/OFF, or 2 fast clicks for strobe. 

Simply unscrew the end cap from your Night Saber Blitzer torch and replace it with the remote switch upgrade. 

The Olight D58 G is a red filter designed for use with the Olight Warrior X Turbo. This filter features a colored lens and rubberized fitting that fits securely over the head of the Warrior X Turbo. Red light filters are great for improving night vision for hunting, travel or tactics.

The Olight 21700 is a powerful Li-ion battery designed for use in the Olight flashlights such as the Warrior X. This battery can bring out the full power of your torch, keeping it charged up for extended periods of time. Li-ion chemistry is strong, stable and charges quickly

Specifications:

• Battery Size: 21700
• Battery Chemistry: Li-Ion (INR)
• Nominal Voltage: 3.6V
• Nominal Capacity: 5000mAh